Canon 5D mark II Firmware 2.03 更新連結
<p><a href="http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=DownloadDetailTabAct&fcategoryid=314&modelid=17662">http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=DownloadDetailTabAct&fcategoryid=314&modelid=17662</a></p><p>可以更新了</p>
<p>http://www.rainbowphoto.com.tw/services/anounce_990316.htm<br><br>NTSC︰<br>1920 x 1080︰改為30 fps (實際為29.97 fps)<br>1920 x 1080︰增加24 fps (實際為23.976 fps)<br>640 x 480︰改為30 fps (實際為29.97 fps)<br><br>PAL︰<br>1920 x 1080︰增加25 fps (實際為25.0 fps)<br>1920 x 1080︰增加24 fps (實際為23.976 fps)<br>640 x 480︰增加25 fps (實際為25.0 fps)<br><br>2. 增加手動調整錄音音量功能 (64級)<br>3. 拍攝短片時的手動曝光狀況可在影像資訊圖上顯示 (光暗度或RGB)<br>4) 於短片拍攝功能中加入快門先決 (TV) 及光圈先決 (AV) 模式<br>5) 聲音取樣頻率從44.1 KHz改為48 KHz<br>6) 解決使用CMOS感應器手動清潔後,機身與鏡頭接合偶爾中斷的現象*<br>* 此現象只影響使用韌體版本1.2.4之相機。</p>
<p>Firmware Version 2.0.3 incorporates five enhancements to the movie function and a fix to the manual sensor cleaning function of the EOS 5D Mark II camera.</p>
<ol>
<li>Adds or changes the following movie frame rates.</li><br>NTSC:
<ul>
<li>1920×1080 : 30 fps (changed - actual 29.97 fps)</li>
<li>1920×1080 : 24 fps (added - actual 23.976 fps)</li>
<li>640×480 : 30 fps (changed - actual 29.97 fps)</li></ul>PAL:
<ul>
<li>1920×1080 : 25 fps (added - actual 25.0 fps)</li>
<li>1920×1080 : 24 fps (added - actual 23.976 fps)</li>
<li>640×480 : 25 fps (added - actual 25.0 fps)</li><br></ul>
<li>Adds a function for manually adjusting the sound recording level (64 levels).</li>
<li>Adds a histogram display (brightness or RGB) for shooting movies in manual exposure.</li>
<li>Adds shutter-priority AE mode (Tv) and aperture-priority AE (Av) mode to the exposure modes for shooting movies.</li>
<li>Changes the audio sampling frequency from 44.1 KHz to 48 KHz.</li>
<li>Fixes a phenomenon where communication between the camera and the attached lens is sometimes interrupted after manual sensor cleaning. (This phenomenon only affects units with Firmware Version 1.2.4.)</li></ol>
<p>Firmware Version 2.0.3 is for cameras with firmware up to version 1.2.4. If the camera's firmware is already version 2.0.3, it is not necessary to update the firmware.</p>
<p>Movies captured using EOS 5D Mark II cameras with Firmware Version 1.1.0 to 1.2.4 can be played back on cameras updated with Firmware Version 2.0.3. However, if you try to play back movies captured with a camera with the new firmare on a camera with a previous firmare version, a message, Cannot play back image, appears on the camera's LCD monitor.</p><p><br></p>
[ 本帖最後由 BlueMark 於 2010-3-19 13:21 編輯 ]
今天最Hot的新聞
補個Canon日本官網的鏈結<div>http://web.canon.jp/imaging/eosd/firm-e/eos5dmk2/firmware.html</div><div><br></div><div>底下有非常詳細的操作圖文說明</div> 請問update後您的機器還有中文介面嗎? 是的,而且所有設定依舊 更新之後我的破解神燈不知道可不可以用
.... 能秀幾張您<div><br></div><div>update後5DII設定的照片</div><div><br></div><div>還有功能有差嗎?</div> 那沒有720p的嗎? <P>1.720P無60P模式</P>
<P>2.對於使用5D2來攝影者最大福音是29.97與23.976FPS可以不會在後製時產生影音不同步,23.976FPS也給喜好電影般影像流暢24P喜好者多個選擇(可惜快門仍舊是1/30秒最低值而不是1/24秒)。</P>
<P>3.聲音可以手動調整就可減少爆音產生兩秒的自動消音缺點,更提高了音頻取樣至48Khz</P>
<P>4.影片紀錄可以看光明暗度或RGB圖,增加拍攝時的影像色階確認正確曝光</P>
<P>這些都比較針對於影片的拍攝實用性的方面</P>
[ 本帖最後由 johnson_choa 於 2010-3-17 11:00 編輯 ] johnson_choa前輩
能分享update後的新功能嗎?
回覆 9# 的帖子
http://www.hd.club.tw/thread-39133-1-2.html這裡有討論介紹過 <P>4.影片紀錄可以看光明暗度或RGB圖,增加拍攝時的影像確認正確曝光 </P>
<P> </P>
<P>請問一下這怎麼叫出來<IMG border=0 alt="" src="http://www.hd.club.tw/images/smilies/default/28.gif" smilieid="111"> </P>
[ 本帖最後由 shishj 於 2010-3-16 22:22 編輯 ]
回覆 11# 的帖子
<P>於M模式live view中,按info鈕或拍完影像play時也可以,選擇拍攝的檔案按info鍵,以前只支援照片模式現今可去查錄影各個時間點的値</P>[ 本帖最後由 johnson_choa 於 2010-3-17 09:33 編輯 ] 原帖由 <i>johnson_choa</i> 於 2010-3-16 15:46 發表 <a href="http://www.hd.club.tw/redirect.php?goto=findpost&pid=457669&ptid=40480" target="_blank"><img src="http://www.hd.club.tw/images/common/back.gif" alt="" border="0"></a> (可惜快門仍舊是1/30秒最低值而不是1/24秒)... <br><br>我在國外一知名的攝影交流網站上看到他們一段教學短片,他們說到快門設定最好是frame值的兩倍,比如30fps就用1/60快門,24的話就用1/48,這樣子比較不會有所謂的jerkiness,不知道中文叫什麼。我是沒親身試過,不知道有沒有差,不過拍片用1/24快門好像不太理想吧?<br><br><br> 等了快一年了, 終於出來了 <P>當 fast camera panning 或 拍 fast moving object 時. 以下的情況最明顯 (based on same frame rate such as 24, 29.97, 高速fps 另計):</P>
<P> </P>
<P>(1) shutter speed 越高 (i.e, 1/125sec, 1/250sec...for 5D2), jerkiness/strobing 畫面跳躍不連續感越明顯 (不自然; 但特殊效果考量除外)</P>
<P>(2) shutter speed 越低 (i.e, 1/30sec, 1/25sec, 1/15sec...), motion blur 越明顯 (or named smeary looks) (不傳神,但特殊效果, 低光考量除外)</P>
<P> </P>
<P>依據傳統 film camera 預設都是 180度快門設定, 5d2 拍29.97fps 搭 1/60sec, 24fps 搭1/50sec, 最自然最接近 film looks </P>
<P> </P>
<P> </P>
<P>原帖由 <I>htjmartin</I> 於 2010-3-18 01:15 發表 <A href="http://www.hd.club.tw/redirect.php?goto=findpost&pid=459972&ptid=40480" target=_blank><IMG border=0 alt="" src="http://www.hd.club.tw/images/common/back.gif"></A> 我在國外一知名的攝影交流網站上看到他們一段教學短片,他們說到快門設定最好是frame值的兩倍,比如30fps就用1/60快門,24的話就用1/48,這樣子比較不會有所謂的jerkiness,不知道中文叫什麼。我是沒親身試過,不知道有沒有差,不 ... </P>
升級前 (1.2.4) vs 升級後 (2.0.3)
<P>升級前 (1.2.4) vs 升級後 (2.0.3)</P><P>若能做到 1920x1080/60i, 那就真要拍拍手, 若是 720p/60p 和 1080/60p 有也, 那就要跟 canon鞠躬了</P>
<P>(Digi4 chip 應該不夠力, 未來要加搭載DiG!C DV 4 可能才有辦法吧)</P>
<P> </P>
<P><BR> </P>
<TABLE border=1 width="95%">
<TBODY>
<TR>
<TD width="20%">
<OL>
<LI>
<DIV align=center><STRONG>NTSC</STRONG></DIV></LI></OL></TD>
<TD colSpan=2>
<DIV align=center>Firmware Version 2.0.3<BR>frame rate (fps)</DIV></TD>
<TD colSpan=2>
<DIV align=center>Firmware Version 1.2.4 or earlier<BR>frame rate (fps)</DIV></TD></TR>
<TR>
<TD>
<DIV align=center>Recording size</DIV></TD>
<TD width="18%">
<DIV align=center>Listed</DIV></TD>
<TD width="19%">
<DIV align=center>Actual</DIV></TD>
<TD width="22%">
<DIV align=center>Listed</DIV></TD>
<TD width="21%">
<DIV align=center>Actual</DIV></TD></TR>
<TR>
<TD>
<DIV align=center>1920×1080</DIV></TD>
<TD>
<DIV align=center>30</DIV></TD>
<TD>
<DIV align=center>29.97</DIV></TD>
<TD>
<DIV align=center>30</DIV></TD>
<TD>
<DIV align=center>30.00</DIV></TD></TR>
<TR>
<TD>
<DIV align=center>1920×1080</DIV></TD>
<TD>
<DIV align=center>24</DIV></TD>
<TD>
<DIV align=center>23.976</DIV></TD>
<TD>
<DIV align=center>-</DIV></TD>
<TD>
<DIV align=center>-</DIV></TD></TR>
<TR>
<TD>
<DIV align=center>640×480</DIV></TD>
<TD>
<DIV align=center>30</DIV></TD>
<TD>
<DIV align=center>29.97</DIV></TD>
<TD>
<DIV align=center>30</DIV></TD>
<TD>
<DIV align=center>30.00</DIV></TD></TR></TBODY></TABLE><BR>
<TABLE border=1 width="95%">
<TBODY>
<TR>
<TD width="20%">
<DIV align=center><STRONG>PAL</STRONG></DIV></TD>
<TD colSpan=2>
<DIV align=center>Firmware Version 2.0.3<BR>frame rate (fps)</DIV></TD>
<TD colSpan=2>
<DIV align=center>Firmware Version 1.2.4 or earlier<BR>frame rate (fps)</DIV></TD></TR>
<TR>
<TD>
<DIV align=center>Recording size</DIV></TD>
<TD width="18%">
<DIV align=center>Listed</DIV></TD>
<TD width="19%">
<DIV align=center>Actual</DIV></TD>
<TD width="22%">
<DIV align=center>Listed</DIV></TD>
<TD width="21%">
<DIV align=center>Actual</DIV></TD></TR>
<TR>
<TD>
<DIV align=center>1920×1080</DIV></TD>
<TD>
<DIV align=center>25</DIV></TD>
<TD>
<DIV align=center>25.00</DIV></TD>
<TD>
<DIV align=center>30</DIV></TD>
<TD>
<DIV align=center>30.00</DIV></TD></TR>
<TR>
<TD>
<DIV align=center>1920×1080</DIV></TD>
<TD>
<DIV align=center>24</DIV></TD>
<TD>
<DIV align=center>23.976</DIV></TD>
<TD>
<DIV align=center>-</DIV></TD>
<TD>
<DIV align=center>-</DIV></TD></TR>
<TR>
<TD>
<DIV align=center>640×480</DIV></TD>
<TD>
<DIV align=center>25</DIV></TD>
<TD>
<DIV align=center>25.00</DIV></TD>
<TD>
<DIV align=center>30</DIV></TD>
<TD>
<DIV align=center>30.00</DIV></TD></TR></TBODY></TABLE>
<P> </P> 大家來 升級<div><br></div>
IT守則一,別急著升級
一個關於 FW 2.0.3討論中的 Bug (於C mode下,無Audio收錄)<div>http://5dmark2.wordpress.com/2010/03/17/bugs-issues-on-firmware-2-0-3/</div> 5DII更新後FCP 要用compressor 轉成PRORES 422時 ~會非常爽... @吐舌@ 原本用compressor轉5DII檔速度很快
可以直接匯入跟匯出...
更新後變的非常慢...
慢到要抓狂...
一次匯入多個檔案還會當機
30fps變成29.97fps之後就是如此...
我請朋友用他的APPLE筆電試也是如此...
SHIT!
頁:
[1]
2